README update

example_jiecang_desk_controller.yaml

@@ -1,116 +0,0 @@
-esphome:
-  name: jiecang-desk-controller
-  friendly_name: Jiecang Desk Controller
-  on_boot:
-    # This script is required to initialize the following sensors:
-    #    height_pct, height_min, height_max, position1 - position4
-    # You can skip this if you don't use those.
-    priority: 0 # when mostly everything else is done
-    then:
-      - lambda: "id(my_desk).request_physical_limits();"
-      - delay: 0.1s # give controller a chance to handle the response before sending the next command
-      - lambda: "id(my_desk).request_limits();"
-      - delay: 0.1s
-      - lambda: "id(my_desk).request_settings();"
-
-external_components:
-  - source:
-      type: git
-      url: https://github.com/Rocka84/esphome_components/
-    components: [ jiecang_desk_controller ]
-
-uart:
-  id: uart_bus
-  tx_pin: TX
-  rx_pin: RX
-  baud_rate: 9600
-
-logger:
-  baud_rate: 0 # disable logging over uart, required when using the RX/TX pins for the controller
-
-jiecang_desk_controller:
-  id: my_desk
-  sensors:
-    height:
-      name: "Height"
-    height_min:
-      name: "Height Min"
-    height_max:
-      name: "Height Max"
-    height_pct:
-      name: "Height Percent"
-    position1:
-      name: "Position 1"
-    position2:
-      name: "Position 2"
-    position3:
-      name: "Position 3"
-    position4:
-      name: "Position 4"
-  buttons:
-    raise:
-      name: "Raise"
-    lower:
-      name: "Lower"
-    stop:
-      name: "Stop"
-    position1:
-      name: "Position 1"
-    position2:
-      name: "Position 2"
-    position3:
-      name: "Position 3"
-    position4:
-      name: "Position 4"
-    save_position:
-      name: "Save Position"
-  numbers:
-    height:
-      name: "Height"
-
-## lambda usage
-# button:
-#   - platform: template
-#     name: "Raise"
-#     on_press:
-#       lambda: "id(my_desk).raise();"
-#   - platform: template
-#     name: "Lower"
-#     on_press:
-#       lambda: "id(my_desk).lower();"
-#   - platform: template
-#     name: "Stop"
-#     on_press:
-#       lambda: "id(my_desk).stop();"
-#   - platform: template
-#     name: "Position 2"
-#     on_press:
-#       lambda: "id(my_desk).goto_position(2);"
-#   - platform: template
-#     name: "Save Position 4"
-#     on_press:
-#       lambda: "id(my_desk).save_position(4);"
-#   - platform: template
-#     name: "Go to 100cm"
-#     on_press:
-#       lambda: "id(my_desk).goto_height(100);"
-
-
-# the usual stuff
-
-esp8266:
-  board: esp01_1m
-
-wifi:
-  ssid: !secret wifi_ssid
-  password: !secret wifi_password
-  ap:
-    ssid: "esphome-desk"
-    password: "9ebc6eac0b4e0e26b8d3b955ec660557"
-
-captive_portal:
-api:
-  encryption:
-    key: !secret encryption_key
-ota:
-

example_jiecang_desk_controller.yaml

@@ -0,0 +1 @@
+components/jiecang_desk_controller/example_basic.yaml